How to Install a Bathtub ( Guide).
How to Install a Bathtub ( Guide).
Blog Article
On this page in the next paragraph you'll find a good deal of reliable resources regarding Installing A Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bath tub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can relocate rapidly; if you need to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to consider employing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a brand-new bathtub and also don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has been used at least when as this will certainly settle it into its final placement.
Planning for the Setup
First of all, the supporting structure provided with the bath should be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently readily available on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on Installing A Bathtub from a friend on our other website. Do you know about somebody who is sincerely interested in the subject? Feel free to share it. I am grateful for your time. Visit again soon.
Maintenance Sign-Up Report this page